|
Search Results for "cisco fast ethernet"

Narrow your selection:

Community Discussions

See Results from:

Showing 1-20 of 77 Results
1  2  3  4
...between a dell pc6248 and a Cisco router. The trouble is i lost...configuration on switch: interface ethernet 1/g48 switchport mode...add 1-2 exit interface ethernet 1/g43 switchport mode...exit On router interface fast 0/1 no ip address no...unttag VLAN (same as native in Cisco), and i can configure VLAN...
1/15/2014  |  (Forums)

...100.187.2 interface ip 10.100.187.2 ospf exit interface ip 10.100.187.2 ospf cost 1 exit ========== Cisco 2620 - 10.100.187.1 ========== ...
2/3/2008  |  (Forums)

...that require me to turn 3 new cisco 2960 L2 switches into trunks...from a pc connected off of the cisco switch, but I am unable to...configs for both the dell and the cisco switch minus proprietary information...255.255.0 192.168.10.100 ip route 192.168...
11/1/2010  |  (Forums)

I just put a new PowerConnect 2724 switch in service replacing an existing Cisco 2924XL enterprise 10/100 switch. I was expecting to see some increased performance in our workstations, but cannot. In fact...
5/28/2007  |  (Forums)

...network. I have a Cisco Router with the following...100 router-id 10.100.1.5 log-adjacency-changes...30 [110/76] via 10.100.1.5 11:43...30 [110/76] via 10.100.1.5 11:43...offices where I have a Cisco Layer 3 switch...
4/20/2006  |  (Forums)

...connection VLAN config on CISCO multicast> (enable...2-20 and set config (CISCO) begin ! ...set interface sc0 1 10.10.100.100/255.0.0.0 10... #module 2 : 52-port 10/100/1000 Ethernet set vlan...

...other traffic) from a 2nd SSID on the Cisco AP to the pfSense DHCP server. Here's the general setup: Cisco 1140 AP with 2 SSIDs/VLANs. Native...It is enabled for a range of IPs in the 10.100.1/24 subnet. I've also created...
(Forums)

...known configuration for the dell and cisco trying to get them to come up with no luck. I set the cisco's VTP to transparent didn't work...shows a link but when i switch it to 10/100/1000 the Cisco gets a link light and the dells link...
5/10/2006  |  (Forums)

...1-2,10-11 no shutdown Cisco 6509 (CATOS) #channelprotocol... ! #module 1 : 48-port 10/100/1000BaseT Ethernet ! #module 2 : 48-port 10/100/1000BaseT Ethernet ! #module 3 : 48-port 10/100/1000BaseT Ethernet ! ...
9/16/2013  |  (Forums)

...uplink a PowerConnect 5324 to a Cisco 4006 with a 24 port gig module...switch. If I set the port to 10/100, it works fine. If I uplink...to a fiber module on the same Cisco switch, it works fine. If...to be specifically related to Cisco's gig module and the PowerConnect...
11/4/2004  |  (Forums)

Hello, I currently have a Cisco ASA 5520 (firewall) that I am trying to...Interface (attached to Host with IIS) 10.10.100.2 255.255.255.0 Host with IIS: 10.10.100.10 255.255.255.0 Any suggestions...
8/18/2006  |  (Forums)

...in a large office. Most of them are Precision 340 with integrated 3C920 NIC. They connect to a Cisco Catalyst 6500 switch, on a 48 port 10/100 switch module (WS-X6348-RJ-45) The problem is some workstations occasionly loose the network...
2/25/2004  |  (Forums)

...gotten it to work with any 10/100 based devices properly. This switch is connected to a Cisco 2620, PIX 520, and VPN...around this. In fact, no 10/100 based devices (access points...cannot put Gb NIC's in the Cisco devices, so we need this...
1/17/2005  |  (Forums)

...Configuration Cisco 3032/3130G-S...Support Steps to Fast Configuration ...connect to Fabric A, Ethernet. Each server also...to 20 External 10/100/1000BASE-T copper...installation of the Cisco X2 transceiver module...modules operate at 10/100/1000 Mb/s and...autonegotiation. Only Cisco SFPs are supported...
11/2/2011  |  (Wikis)

... kwillse Anyone using Cisco Catalyst 3750 switches for... Jumbo frames support the Cisco; Stackwise technology supports...Jumbo frames up to 9 KB on the 10/100/1000 copper ports for...packets is not supported by the Cisco Catalyst 3750. However...
11/14/2011  |  (Wikis)

...are considering purchasing the Cisco SG 200-18P to connect all our server...a 1.25Gbps fiber using the “Cisco SG 200-18P” and the second question...considering replacing the 3348 with Cisco SG200-50 10/100/1000 switch. Same questions apply...
(Forums)

...10895.3010 System Up Time................................. 1 days 14 hrs 11 mins 5 secs 10/100 Ethernet/802.3 interface(s)............. 5 Gig Ethernet/802.3 interface(s)................ 2 10Gig Ethernet/802.3 interface(s...

...doing was wiping out both the Cisco router and the Dell switch and starting from scratch. On the cisco router I created 3 VLAN's and 3 sub interfaces for the ethernet port, assigning each sub interface...2.30.34 from 10.2.10.100 will get a reply? ...

...PowerConnect M8428-k CMC 3.1 Dell 10/100/1000Mb Ethernet Pass-Through CMC 1.0 Dell... Brocade M5424 CMC 1.2 Cisco Catalyst CBS 3130X-S CMC 1.0... Brocade M6505 CMC 4.3 Cisco Nexus B22DELL CMC 4.3
(Forums)

...have switches witn 2 gig uplinks and 48 10/100/100 gig eithernet ports I want...to be on ip 172.16.4.x attached to cisco router port GE1/0/0 i want the...be on ip 172.16.14.x attached to cisco router port GE1/0/1 The router...

1  2  3  4
Showing 1-20 of 77 Results
Provide Search Feedback
Were you satisfied with your search experience?
Yes
No
| Write and Tell Us More
snUX01