|
Search Results for "cisco fast ethernet"

Narrow your selection:

Community Discussions

See Results from:

Showing 1-20 of 103 Results
1  2  3  4  5  6
...between a dell pc6248 and a Cisco router. The trouble is i lost...configuration on switch: interface ethernet 1/g48 switchport mode...add 1-2 exit interface ethernet 1/g43 switchport mode...exit On router interface fast 0/1 no ip address no...unttag VLAN (same as native in Cisco), and i can configure VLAN...
1/15/2014  |  (Forums)

...32 [110/12] via 10.100.1.5 0:34:22...32 [110/12] via 10.100.1.5 0:34:22... Cisco 3825 ...subnetted, 2 subnets O 10.100.0.0 [110/2... Cisco 2800 ...

...access-list 110 deny ip 10.100.0.0 0.0.255.255...access-list 110 permit ip 10.100.0.0 0.0.255.255...20 INET Router - Cisco 2801 Router - IOS Ver...FastEthernet0/1 ip address 10.100.1.254 255.255.0...

...100.187.2 interface ip 10.100.187.2 ospf exit interface ip 10.100.187.2 ospf cost 1 exit ========== Cisco 2620 - 10.100.187.1 ========== ...
2/3/2008  |  (Forums)

...that require me to turn 3 new cisco 2960 L2 switches into trunks...from a pc connected off of the cisco switch, but I am unable to...configs for both the dell and the cisco switch minus proprietary information...255.255.0 192.168.10.100 ip route 192.168...
11/1/2010  |  (Forums)

Are the client machines 10/100 or full gigabit?

Search for a program called QCheck. I use to test it with my wireless. Should work just fine.

I just put a new PowerConnect 2724 switch in service replacing an existing Cisco 2924XL enterprise 10/100 switch. I was expecting to see some increased performance in our workstations, but cannot. In fact...
5/28/2007  |  (Forums)

...connection VLAN config on CISCO multicast> (enable...2-20 and set config (CISCO) begin ! ...set interface sc0 1 10.10.100.100/255.0.0.0 10... #module 2 : 52-port 10/100/1000 Ethernet set vlan...

...network. I have a Cisco Router with the following...100 router-id 10.100.1.5 log-adjacency-changes...30 [110/76] via 10.100.1.5 11:43...30 [110/76] via 10.100.1.5 11:43...offices where I have a Cisco Layer 3 switch...
4/20/2006  |  (Forums)

...other traffic) from a 2nd SSID on the Cisco AP to the pfSense DHCP server. Here's the general setup: Cisco 1140 AP with 2 SSIDs/VLANs. Native...It is enabled for a range of IPs in the 10.100.1/24 subnet. I've also created...
(Forums)

...tie them together. Set as dot1q on the Cisco side and also tried it not as a trunked/tagged port on Cisco and the Dell - so its acting like a bridge...about the gig port and just tie them with 10/100 cat 5, it works great - in dont1q trunk...

...1# sho ip ospf database OSPF Router with ID 10.100.1.1 Router Link States(Area 0.0...0.6 10.2.0.6 1823 0x80000468 0x0b74 1 10.100.1.1 10.100.1.1 1030 0x800001e9 0x6b35 1 10.100.1...

...known configuration for the dell and cisco trying to get them to come up with no luck. I set the cisco's VTP to transparent didn't work...shows a link but when i switch it to 10/100/1000 the Cisco gets a link light and the dells link...
5/10/2006  |  (Forums)

...1-2,10-11 no shutdown Cisco 6509 (CATOS) #channelprotocol... ! #module 1 : 48-port 10/100/1000BaseT Ethernet ! #module 2 : 48-port 10/100/1000BaseT Ethernet ! #module 3 : 48-port 10/100/1000BaseT Ethernet ! ...
9/16/2013  |  (Forums)

All ports on the switch simply forward traffic based on MAC address. The only difference between the 10/100 and 10/100/1000 ports is the speed. If the other devices are not capable of gigabit connectivity, it would be pointless...

...uplink a PowerConnect 5324 to a Cisco 4006 with a 24 port gig module...switch. If I set the port to 10/100, it works fine. If I uplink...to a fiber module on the same Cisco switch, it works fine. If...to be specifically related to Cisco's gig module and the PowerConnect...
11/4/2004  |  (Forums)

...26 GBIC enabled? By default the built in 10/100/1000BAST-T port is enabled which is...a GBIC module instead of the built-in 10/100/1000BASE-T port for a Gigabit Ethernet...port disables the associated built-in 10/100/1000BASE-T port. When the...

Hello, I currently have a Cisco ASA 5520 (firewall) that I am trying to...Interface (attached to Host with IIS) 10.10.100.2 255.255.255.0 Host with IIS: 10.10.100.10 255.255.255.0 Any suggestions...
8/18/2006  |  (Forums)

What I'm saying is that I can use that very same port but force it to 10/100 instead of 1000, and it works fine.

1  2  3  4  5  6
Showing 1-20 of 103 Results
Provide Search Feedback
Were you satisfied with your search experience?
Yes
No
| Write and Tell Us More
snUX04