|
Search Results for "full duplex port"

Narrow your selection:

See Results from:

Find Results In:

Showing 41-60 of 420 Results
1  2  3  4  5  6
...when connected to 10Mbps only port. It started to happen after we...switch ports are set to 100Mbps / Full Duplex. They do not autonegotiate...workstation side, we also forced the port to 100Mbps / Full Duplex. In order to isolate the problem...
2/25/2004  |  (Forums)

...Enabled* Ethernet port: 1 Link status: Up...mode: Auto-negotiate Port speed: 100 Mbps Duplex mode: Full duplex IPv4 settings...mode: Auto-negotiate Port speed: 100 Mbps Duplex mode: Full duplex IPv4 settings...

...available MAC address exists which can be assigned to a port. • Auto-negotiation mode is not configured on the port. • The port is in full-duplex mode. • All ports in the LAG have the same...
9/8/2008  |  (Forums)

...Disabled Ethernet port: 1 Link status...Manual setting Port speed: 100 Mbps Duplex mode: Full duplex IPv4 settings...Manual setting Port speed: 100 Mbps Duplex mode: Full duplex IPv4 settings...

...mode are, the ones not in managed mode are not. We are using auto-negotiation on all the links, and the port lights indicate full duplex. The error that we get is a windows error. When the error happens, a windows error pops on the screen...

...with no speed issues... W2k8 is a different deal, but I would have to believe it is either a network port setting (full/half duplex or 100/1000, etc...). If you have ruled that out then I would look at the iSCSI MPIO, etc.

...ether-options { link-mode full-duplex; speed { 1g...ethernet-switching { port-mode access; vlan...ether-options { link-mode full-duplex; speed { 1g...ethernet-switching { port-mode access; vlan...

... Recently upgraded one of our PC 6248 switches to 3.2.0.9. It appears that you can no longer force a port to 1000 Full Duplex. If I disable auto negotiation, the only choices are 10 and 1000. I called support and was told that...
1/11/2011  |  (Forums)

...Disabled Ethernet port: 1 Link status: Up...mode: Manual setting Port speed: 100 Mbps Duplex mode: Full duplex Network configuration...mode: Manual setting Port speed: 100 Mbps Duplex mode: Full duplex Network configuration...
5/11/2009  |  (Forums)

...auto-neg causes link to disconnect/connect every few seconds, have to force to 100 Mbit Full Duplex. In addition, we ordered a few e-port plus replicators - so I thought it might be a problem with the unit, so I simply replaced it...

...Disabled Ethernet port: 1 Link status: Up...mode: Manual setting Port speed: 100 Mbps Duplex mode: Full duplex IPv4 settings...mode: Manual setting Port speed: 100 Mbps Duplex mode: Full duplex IPv4 settings...
7/21/2010  |  (Forums)

...respond within the expected time period. Please try again later." The port speed is 100/Full Duplex on the device and the network switch port matches this. Anybody have any similar problems or ideas on what might be the cause...
3/5/2008  |  (Forums)

...just the way it typically plays out when all connections involved are 1 gigabit, full duplex? Let's say you have a 4 port LAG group at 100 mbps, full duplex, could a single 1 gig device on switch A connect to a single 1 gig device on switch...
11/26/2012  |  (Forums)

...connect the NIC to a gigabit port on a Cisco switch (I have seen...If I force both the switch port and NIC to 100Mbit full duplex rather than letting them auto...directions with auto negotiate and a full duplex gigabit connection. If I connect...
(Forums)

... As a result of my conversations with supportm we have done the following: 1) Set all port settings to 10Mb Full Duplex. 2) Removed all secondary DRAC cards. We have SERIOUS problems with these cards. ...
7/8/2011  |  (Forums)

How may I change the network port speed and duplex from Auto to 100Mb/s Full Duplex on the laser 1710n and 1720dn printers? Unfortunately my ethernet switch requires I fix the speed and duplex to reduce dasta transmission errors and increase throughput.
(Forums)

...issue. Our Cisco switches were statically set for duplex full and speed 1000 on each port that these new Optiplex 9020 were connected to...replaced. Once I removed those entries from the port on the switch everything started working.

...vanilla 5224 and default Gigabit 7606 port config. *) 5224 port capabilities cropped to 1000 full duplex only, cisco on auto or forced to 1000...ports 21-24 are SFP only) No SFP port in 5224 has been ever up with 7606. ...

...802.3x standard for full-duplex links. The flow control...mechanism allows a receiving port to signal the port on the sending device...be configured on any port but will be operational...link is operating in full duplex. The PowerConnect 28xx...

...SigmaTel STAC9750 chipset is an AC '97 CODEC with SPDIF support (via D/Dock and D/Port only) and headphone amplifier. Features include: Full duplex stereo 18-bit ADC and 20-bit DAC AC'97 rev 2.2-compliant SPDIF support...

1  2  3  4  5  6
Showing 41-60 of 420 Results
Provide Search Feedback
Were you satisfied with your search experience?
Yes
No
| Write and Tell Us More
snUX02